ASTM D5276 PDF

ASTM DENGL I 0b3b | This standard is issued under the fixed designation D ; the number immediately following the. This standard is issued under the fixed designation D ; the number immediately 1 This test method is under the jurisdiction of ASTM Committee D10 on. The ASTM-D standard test method for drop test of loaded containers evaluates the capability of a container to withstand the sudden shock resulting from a.

Author: Zolojinn Gucage
Country: Dominican Republic
Language: English (Spanish)
Genre: Spiritual
Published (Last): 28 September 2014
Pages: 232
PDF File Size: 7.16 Mb
ePub File Size: 6.57 Mb
ISBN: 884-8-75440-802-2
Downloads: 8951
Price: Free* [*Free Regsitration Required]
Uploader: Nahn

Replicate samples should be subjected to identical procedues to determine the consistency of the failure point.

The number of test specimens depends on the purpose of the tests but will usually require eleven or more replicate test specimens; using much larger sample sizes will result in higher con?

A normal distribution cannot be assumed for statistical analysis; a log-normal or Weilbull distribution are often better. The pooled reproducibility between laboratory standard deviation was 2. D Terminology of Packaging and Distribution Environments. See Practice D for additional guidance. Neither the depth nor width of the mass shall be less than half the length. Referenced Documents purchase separately The documents listed below asttm referenced within the subject standard but are not provided as part of the standard.

Typical types of drop cycles are as follows: GPO,Chapter Caution—These ISO standards may wstm procedures that do not meet the requirements for this test method. Quality Management View All. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

  CALENDARIO ZARAGOZANO ABRIL 2012 PDF

If this specimen passes at this drop height, the next test will be at a higher drop height with a new package. These ISO standards may describe procedures that do not meet the requirements for this test method. This test method may also be used to compare the performance of different package designs. Research Report D10— describes an interlaboratory test program of three packaged items, establishing drop heights to failure.

Historical Version s – view previous versions of standard. If drop leaves are used, the apparatus shall provide a spring or other mechanism so that the leaves do not interfere with a free, unobstructed fall.

Where a bag or sack has one or more side seams, Side 2 shall include a side seam. While the outer carton almost always deforms, the products may still be protected ashm breakage.

Precision and Bias Where it is desirable to drop on a midpoint between two locations on the sidewall, such a point can be designated using four numbers, that is, drop on Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Repeat the drop or drop cycle on the same package until the prede? Quality control inspection companies often simply refer to it as the carton drop test.

Shortcomings of the drop test of loaded containers ISTA 1A is a procedure designed to challenge the strength and robustness of the product and package combination.

Drop test of loaded containers (cartons), ASTM D5276

For more information visit www. ASTM-D Standard Test Method for Drop Test of Loaded Containers by Free Fall The ASTM-D standard test method for drop test of loaded containers evaluates the capability of a container to withstand the sudden shock resulting from a free fall, or the capability of a container and its d52766 packing to protect its contents during the sudden shock resulting from a free fall.

  DINOSAUR TRAINING BROOKS KUBIK PDF

asfm Sometimes a single drop or drop cycle from a height which caused cumulative damage of this procedure will not cause similar damage to the package or contents. Practice E is recommended. This test method may also permit observation of the progressive failure of a container and the damage to its contents. Continue dropping on similar cycles until a speci? If there are more failures than passes, average the height of the passes and add 1? See Practice D for additional guidance. How can Zstm ensure the total quantity of my goods is shipped?

Drop test of loaded containers (cartons), ASTM D | AQF

Last previous edition D — Replicate samples should be subjected to identical procedures for comparison and for statistical analysis.

Pros and Cons of India or China Manufacturing. The height of each drop is thus determined by the result of the previous test. It is also up to the importer to define whether unit packaging may be damaged or must stay visually intact. See Practice D for additional guidance.

D — 98 8. Astm D Standard These ISO standards may describe procedures that do not meet the requirements for this test method.