LM353 DATASHEET PDF

Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters. LM are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for LM LM Fairchild datasheet pdf data sheet FREE Datasheets (data sheet) search for integrated circuits (ic), semiconductors and other electronic components.

Author: Kagagor Bale
Country: Myanmar
Language: English (Spanish)
Genre: Health and Food
Published (Last): 3 September 2018
Pages: 171
PDF File Size: 20.34 Mb
ePub File Size: 19.26 Mb
ISBN: 193-8-57397-338-9
Downloads: 59245
Price: Free* [*Free Regsitration Required]
Uploader: Tejin

This input current will only exist when the voltage at any of the input leads is driven negative.

(Datasheet) LM pdf – Dual Operational Amplifier (1-page)

Output phase will be correct as long as one of the inputs is within the operating common mode range. Preconditioning the part during normal operation, before the desired synchronizing pulse, is necesasry. The output collector is left open, permitting the designer to drive devices in the range of 2V to 36V.

Response Times Figure This current is essentially constant, independent of the state of the output so no loading change exists on the input lines. If the strobe and balance pins are unused, short them together for maximum AC stability. Undistorted Output Voltage Swing vs.

High degree of isolation between amplifiers: In addition the total supply current xatasheet all four amplifiers is comparable to the Supply current of a single LM datsaheet OP Amp. This is not destructive and normal output states will re-establish when the input voltage again returns to a value greater than 0.

  HITACHI CP-DX300 PDF

A value of 1 indicates an active HIGH pulse. The input offset voltage and input offset current are specified for a logic threshold voltage of I, 1.

LM353 Datasheet

This voltage regulator is exceptionally easy to use and requires only two external resistors to set the output voltage. Therefore, the flip-flop circuit is set and output is high. The start and end times are specified in number of clock cycles per line. The output structures may sink or source mA. A third terminal on the KA Registers 5, 6, and 7 are programmed in this manner.

L353 load both bytes of all 19 registers would require a total of 57 load cycles 19 address and 38 data cycles. Re-scanning the same register will require that register to be reloaded. The normal fault sensitivity is determined by the timing capacitor discharging current, ITH. A special feature is found in circuitry that rapidly resets the integrating timing capacitor in the event that noise pulses introduce unwanted charging currents.

Promote your business on Quora – it’s where people look for reliable information about your industry. R1 Figure 3. Pin 1 Saturation Voltage vs. Output bypass capacitors will improve the transient response of the regulator.

Destructive dissipation can result from simultaneous shorts on all amplifiers. Supply current when output is high is typically 1. Output Saturation Voltage vs. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its datashset or effectiveness.

  BIBLIOTHECA HAGIOGRAPHICA GRAECA PDF

Common Mode LImits vs. Current Limiting Output Current vs.

Other features include input offset currents and input bias current which are much less than those of a standard LM Constant Current Regulator Notes: As reset voltage lowers, timing is inhibited and then the output goes low. The two stage common-emitter output circuit datsheet gain and output sink capacity of 3. Observe package thermal characteristics. Positive Current Limit Output Voltage vs.

Driving TTL Figure 7. Substitution can therefore be made with no change in circuit behavior. Intended for single supply applications, the Darlington PNP input stage allows them to compare voltages that include ground. National Semiconductor Europe Fax: Note that this is an approximate calculation; the exact value of RSET depends datashee the specific sense transformer used and LM tolerances.

Dimension “Q” shall be measured from the seating plane to the base plane. However, the devices can be synchronized slaved to an external timing signal in a limited sense.